# How does this TIFF compare with the fax standards?

> Pick a TIFF and see the compression, width, resolution and fill order of each page set against T.4 and RFC 3949. Read in your browser, never uploaded.

Page: https://faxforagents.com/tools/fax-tiff/
Last changed: 2026-11-16

Updated Nov 16, 2026

Pick a TIFF to see how each page is stored. This page reads the tags that describe each page and sets them against the fax standards ITU-T T.4 and RFC 3949. Your browser does the reading, and the file is never uploaded.

It reads bits per sample, compression, image width, X and Y resolution, fill order and photometric interpretation. Each verdict prints the sentence of the standard it rests on. A value that cannot be read is shown without a verdict. The page does not send the file, and it cannot tell how a fax of it will look.

## Which standards does this page compare with?

ITU-T T.4, edition T.4 (07/03), is the recommendation for Group 3 fax terminals. Its clause 2.1 sets the number of picture elements along a scan line and the vertical resolutions. RFC 3949 describes how fax pages are stored in a TIFF file. It defines profiles, and this page uses its two black and white ones.

- Profile S: Minimal Black-and-White Fax Profile, in [RFC 3949, section 3](https://www.rfc-editor.org/rfc/rfc3949.html). This page calls it profile S.
- Profile F: Extended Black-and-White fax profile, in [RFC 3949, section 4](https://www.rfc-editor.org/rfc/rfc3949.html). This page calls it profile F. Every value profile S lists, profile F lists too.

RFC 3949 has further profiles for colour and grey images, which this page leaves out. Both standards have a row in the [fax standards table](https://faxforagents.com/glossary/#fax-standards) of our glossary, with the edition in force and its official page. We read the sentences below on 2026-11-16. They come from [the text of T.4 (07/03), in English, as a PDF](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) on itu.int and from [the text of RFC 3949](https://www.rfc-editor.org/rfc/rfc3949.html) on rfc-editor.org.

## What is each value set against?

Each field below lists the values the page knows, the verdict each one gets and the sentences behind it. The results use the same words.

### Byte order

- II profile S: Either byte order can be used, except in the case of the minimal black-and-white profile, which SHALL use value "II". [RFC 3949, section 2.1.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- MM profile F, not S: The sentence of [RFC 3949, section 2.1.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.

### Bits per sample tag 258

- 1 profile S: BitsPerSample(258) = 1. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- Not set profile S: Default = 1 (field may be omitted if this is the value). [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html)
- Any other value outside S and F: The sentence of [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.

### Compression tag 259

- 3, with T4Options bit 0 at 0 profile S: This is specified by setting the Compression field value to 3 and then setting bit 0 of the T4Options field to 0. [RFC 3949, section 4.4.4](https://www.rfc-editor.org/rfc/rfc3949.html) Compression(259) = 3. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 3, with no T4Options field outside S and F: Note: The T4Options field is required when the Compression field has a value of 3. [RFC 3949, section 3.2.2](https://www.rfc-editor.org/rfc/rfc3949.html)
- 3, with T4Options bit 0 at 1 profile F, not S: Alternatively, the two dimensional Modified READ (MR) method, which is much less frequently used in historical TIFF-F implementations, may be selected by setting bit 0 of the T4Options field to 1. [RFC 3949, section 4.4.4](https://www.rfc-editor.org/rfc/rfc3949.html) Compression(259) = 3, 4. [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 3, with T4Options bit 1 at 1 outside S and F: Bit 1 must be 0. [RFC 3949, section 3.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- 4, with T6Options at 0 profile F, not S: Depending upon the application, the more efficient two-dimensional Modified Modified READ (MMR)compression method from T.6 may be selected by setting the Compression field value to 4 and then setting the first two bits (and all unused bits) of the T6Options field to 0. [RFC 3949, section 4.4.4](https://www.rfc-editor.org/rfc/rfc3949.html) MMR was originally defined for use with Group 4 facsimile, so that this compression method has been commonly called Group 4 compression. [RFC 3949, section 4.4.4](https://www.rfc-editor.org/rfc/rfc3949.html)
- 4, with no T6Options field outside S and F: 4 = 2-dimensional coding, ITU-T Rec. T.6 (MMR - Modified Modified READ, must have T6Options field)) This is a TIFF Extension value. [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) For FAX, the field must be present and have the value 0. [RFC 3949, section 4.2.2](https://www.rfc-editor.org/rfc/rfc3949.html)
- 4, with T6Options not at 0 outside S and F: The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 4.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- 2 outside S and F: As a result, TIFF-F uses Compression=3 instead of Compression=2 to specify Modified Huffman compression. [RFC 3949, section 4.4.4](https://www.rfc-editor.org/rfc/rfc3949.html)
- Not set outside S and F: Default = 1 (no compression, so may not be omitted for FAX). [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html)
- Any other value outside S and F: The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.

### Image width tag 256

- 1728 profile S: c) 1728 black and white picture elements along the standard scan line length of 215 mm ±1%; [ITU-T T.4, clause 2.1 c)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) This profile only supports a page width of 1728 pixels. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 2048 profile F, not S: d) optionally, 2048 black and white picture elements along a scan line length of 255 mm ±1%; [ITU-T T.4, clause 2.1 d)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) This profile supports the following fixed page widths: 1728, 2592, 3456 (corresponding to North American Letter and Legal and ISO A4 paper sizes), 2048, 3072, 4096 (corresponding to ISO B4 paper size), and 2432, 3648, 4864 (corresponding to ISO A3 paper size). [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 2432 profile F, not S: e) optionally, 2432 black and white picture elements along a scan line length of 303 mm ±1%; [ITU-T T.4, clause 2.1 e)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- 3456 profile F, not S: f) optionally, 3456 black and white picture elements along a scan line length of 215 mm ±1%; [ITU-T T.4, clause 2.1 f)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- 4096 profile F, not S: g) optionally, 4096 black and white picture elements along a scan line length of 255 mm ±1%; [ITU-T T.4, clause 2.1 g)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- 4864 profile F, not S: h) optionally, 4864 black and white picture elements along a scan line length of 303 mm ±1%. [ITU-T T.4, clause 2.1 h)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- 2592, 3072 or 3648 profile F, not S: The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- Not set outside S and F: No default, must be specified. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- Any other value outside S and F: The sentence of [ITU-T T.4, clause 2.1 c)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) quoted above. The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.

### X resolution tag 282

- 200 per inch or 204 per inch profile S: In pixels/inch, the allowed values are 200 and 204, which may be treated as equivalent. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 80 per centimetre profile F, not S: The ITU-T Recommendations for facsimile specify a small number of horizontal resolutions: 100, 200, 300, 400 pixels per inch, and 80, 160 pixels per centimeter (or 204, 408 pixels per inch). [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) ResolutionUnit(296) = 2, 3. [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) ResolutionUnit(296) = 2. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 300 per inch, 400 per inch or 408 per inch profile F, not S: In pixels/inch, the allowed values are 200, 204, 300, 400, and 408. [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 160 per centimetre profile F, not S: The sentence of [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- A unit other than inch or centimetre outside S and F: The sentence of [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The unit of measure for resolution. 2 = inch, 3 = centimeter; Default = 2 (field may be omitted if this is the value) [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html)
- Not set outside S and F: No default, must be specified. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- Any other value outside S and F: The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.

### Y resolution tag 283

- 98 per inch or 100 per inch profile S: In pixels/inch, the allowed values are 98, 100, 196, and 200; 98 and 100 may be treated as equivalent, and 196 and 200 may be treated as equivalent. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) a) a standard resolution of 3.85 lines/mm ± 1% in vertical resolution; [ITU-T T.4, clause 2.1 a)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) The minimal interchange portion of the black-and-white facsimile mode supports 1-dimensional Modified Huffman (MH) compression, with the original Group 3 fax resolutions, commonly called "standard" and "fine." [RFC 3949, section 3.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 38.5 per centimetre profile F, not S: The ITU-T Recommendations for facsimile specify a small number of vertical resolutions: 100, 200, 300, 400 pixels per inch, and 38.5, 77, 154 pixels per centimeter (or 98, 196, 391 pixels per inch). [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) The sentence of [ITU-T T.4, clause 2.1 a)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) quoted above. The sentence of [RFC 3949, section 3.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. ResolutionUnit(296) = 2, 3. [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) ResolutionUnit(296) = 2. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 196 per inch or 200 per inch profile S: The sentence of [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. b) optional higher resolution of 7.7 lines/mm ± 1% and 15.4 lines/mm ± 1% in vertical direction; [ITU-T T.4, clause 2.1 b)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) The sentence of [RFC 3949, section 3.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- 77 per centimetre profile F, not S: The sentence of [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [ITU-T T.4, clause 2.1 b)](https://www.itu.int/rec/dologin_pub.asp?lang=e&id=T-REC-T.4-200307-I!!PDF-E&type=items) quoted above. The sentence of [RFC 3949, section 3.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- 300 per inch, 391 per inch or 400 per inch profile F, not S: In pixels/inch, the allowed values are 98, 100, 196, 200, 300, 391, and 400 pixels/inch. [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 154 per centimetre profile F, not S: The sentence of [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- A unit other than inch or centimetre outside S and F: The sentence of [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The unit of measure for resolution. 2 = inch, 3 = centimeter; Default = 2 (field may be omitted if this is the value) [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html)
- Not set outside S and F: No default, must be specified. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- Any other value outside S and F: The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.

### Fill order tag 266

- 2 profile S: FillOrder(266) = 2. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 1 profile F, not S: FillOrder(266) = 1 , 2. [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) The default bit order in Baseline TIFF per [TIFF] is indicated by FillOrder=1, where bits are not reversed before being stored. [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html)
- Not set profile F, not S: The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above. The sentence of [RFC 3949, section 2.2.2](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.
- Any other value outside S and F: The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.

### Photometric interpretation tag 262

- 0 profile S: PhotometricInterpretation(262) = 0. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- 1 profile F, not S: 0 = pixel value 1 means black, 1 = pixel value 1 means white. [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- Not set outside S and F: No default, must be specified. [RFC 3949, section 3.2.1](https://www.rfc-editor.org/rfc/rfc3949.html)
- Any other value outside S and F: The sentence of [RFC 3949, section 4.2.1](https://www.rfc-editor.org/rfc/rfc3949.html) quoted above.

A tag whose value cannot be read, because it points outside the file or has the wrong type, is shown as unreadable, with no verdict.

## How many pages and how large a file can you send?

The file is also set against the [API limits](https://faxforagents.com/docs/limits/). A document has at most 200 pages, an uploaded file is at most 25 MiB, and one image frame is at most 50 million pixels. A larger file is not read here, because the API would refuse it at upload. All the frames of a file together are at most 1683 million pixels.

To [send a fax online](https://faxforagents.com/send-a-fax/) by card, one order takes at most 20 pages and a file of 10 MiB. The results say when a file is over either of those.

The API takes TIFF uploads, as the [images section of the send fax docs](https://faxforagents.com/docs/send-fax/#images) describes. Each frame of a multi-page TIFF is one page there, and every page becomes 8-bit grayscale on a US letter page, scaled to fit. The API does not set a TIFF against profiles S and F, so a file outside them is converted in the same way.

## What does this page leave out?

- The image itself. No pixel is decoded, so the page cannot say whether the compressed data is sound or how the page looks.
- Whether the API can convert the file. The API decodes every frame, and a file can be refused for a reason this page cannot see.
- Which widths go with which resolutions. RFC 3949 pairs them in a table for profile F, and this page sets each value against its own list only.
- Other tags that RFC 3949 asks for, such as the page number, the strips and the subfile type. Of the coding options, only the bits named above are read.
- The colour, grey and other profiles of RFC 3949. A colour or grey TIFF shows values outside S and F.
- BigTIFF, the form with 64-bit offsets. The page names it and does not read it.

## How is the file read?

The page reads the TIFF header and the list of tags that describes each page. It uses a small reader of its own, served from this site. It does this in a separate thread of your browser, which starts when you pick a file. Nothing is fetched from anywhere else, and nothing in the file is run.

A file gets 10 seconds. After that the reader stops. A file longer than the page limit is read up to the limit. A file that breaks off part way shows the pages before the break. The file stays on your device. The site's analytics count the visit, as on every page, and are told to leave the results out. Reload the page and the results are gone.
