How long does this document take on a fax line?

Updated

Pick a PDF or TIFF to see its fax transmission time, how long its pages take on a fax line. This page codes each page the way a Group 3 fax machine does, then works out the seconds at the modem rate you pick. Your browser does the work, and the file is never uploaded.

The figure is the page data alone. The call set-up, the modem training, the confirmation after each page, retries and a busy line all add time. Our measured times show how much on our own faxes.

Time a PDF or TIFF

Drop a PDF or TIFF here

or

Read in this browser only. The file is never uploaded, and its name is not shown or kept.

Settings

How long did our own faxes take?

Measured on our own live faxes between 2026-11-09 and 2026-11-13
PagesFrom the send to the final reportThe call itself
1 page29 to 34 seconds25 seconds
2 pages35 to 59 seconds31 seconds
8 pages327 seconds313 seconds

We measured these times on our own live faxes between and , from the send to the carrier's final report. They are a measurement, never a promise. The same figures are in facts.json, and our post on how long a fax takes explains them.

What does the figure cover?

The figure is the page data of a call, as T.4 defines it, at the rate and minimum scan line time you pick. For each page it adds up these parts.

The total coded scan line is defined as the sum of data bits plus any required fill bits plus the end-of-line (EOL) bits. ITU-T T.4, clause 3

A real call takes longer. Before the pages, the machines answer, state what they can do, agree on the rate and train the modems. After each page the receiver confirms it, and a page can be sent again. All of that is in the procedure of T.30, and none of it is in this figure. Compare it with the calls in our table above: the gap is the rest of the call.

How is a page coded?

Each page is laid on the scan line at its own size and centred. A page wider than the line is scaled down to fit it. The line has 1728 picture elements, or pels, along 215 mm.

A total of 1728 picture elements represent one horizontal scan line of 215 mm length. ITU-T T.4, clause 4.1.1

Down the page, standard resolution has 3.85 scan lines per millimetre and fine has 7.7. These are the two resolutions our fax TIFF page sets files against.

a) a standard resolution of 3.85 lines/mm ± 1% in vertical resolution; ITU-T T.4, clause 2.1 a)

b) optional higher resolution of 7.7 lines/mm ± 1% and 15.4 lines/mm ± 1% in vertical direction; ITU-T T.4, clause 2.1 b)

Each pel is the average of the pixels it covers, and a pel darker than mid-grey is black. A TIFF whose pixels already match the pels and lines to within 1% is coded pixel for pixel.

A fax TIFF is 1728 pels wide at 200 or 204 per inch. Its rows are coded one for one as standard lines at 98 or 100 lines per inch, and as fine lines at 196 or 200. Our fax TIFF page quotes the profile of RFC 3949 that treats those values as equal.

In pixels/inch, the allowed values are 200 and 204, which may be treated as equivalent. RFC 3949, section 3.2.1

In pixels/inch, the allowed values are 98, 100, 196, and 200; 98 and 100 may be treated as equivalent, and 196 and 200 may be treated as equivalent. RFC 3949, section 3.2.1

Each line is then coded with the one-dimensional scheme of T.4, called Modified Huffman. A line is a row of runs, white and black in turn, and each run has its code word.

In order to ensure that the receiver maintains colour synchronization, all data lines will begin with a white run length code word. ITU-T T.4, clause 4.1.1

If the actual scan line begins with a black run, a white run length of zero will be sent. ITU-T T.4, clause 4.1.1

Run lengths in the range of 0 to 63 pels are encoded with their appropriate terminating code word. ITU-T T.4, clause 4.1.1

Run lengths in the range of 64 to 1728 pels are encoded first by the make-up code word representing the run length which is equal to or shorter than that required. ITU-T T.4, clause 4.1.1

This is then followed by the terminating code word representing the difference between the required run length and the run length represented by the make-up code. ITU-T T.4, clause 4.1.1

This code word follows each line of data. ITU-T T.4, clause 4.1.2

In addition, this signal will occur prior to the first data line of a page. ITU-T T.4, clause 4.1.2

Fill must be added to ensure that the transmission time of Data, Fill and EOL is not less than the minimum transmission time of the total coded scan line established in the pre-message control procedure. ITU-T T.4, clause 4.1.3

The end of a document transmission is indicated by sending six consecutive EOLs. ITU-T T.4, clause 4.1.4

So a blank line is one white run of 1728 pels: a make-up code word, a terminating code word of zero and the EOL. A line of dense text has many short runs, and many more bits. In Figure 2 of T.4, the EOL of the last line is the first of the 6 that end the page.

Which modem rates and scan line times can you pick?

The rates are the ones the DCS frame of T.30 can set. In that frame the sending machine picks the rate for the call. The 33 600 bit/s rate is the top of the V.34 title.

The modem rates this page offers and where each one is written
RateModemSource
2400 bit/s V.27ter 2400 bit/s, ITU-T Rec. V.27 ter T.30, Table 2, bits 11 to 14, DCS
4800 bit/s V.27ter 4800 bit/s, ITU-T Rec. V.27 ter T.30, Table 2, bits 11 to 14, DCS
7200 bit/s V.29 or V.17 7200 bit/s, ITU-T Rec. V.29 7200 bit/s, ITU-T Rec. V.17 T.30, Table 2, bits 11 to 14, DCS
9600 bit/s V.29 or V.17 9600 bit/s, ITU-T Rec. V.29 9600 bit/s, ITU-T Rec. V.17 T.30, Table 2, bits 11 to 14, DCS
12 000 bit/s V.17 12 000 bit/s, ITU-T Rec. V.17 T.30, Table 2, bits 11 to 14, DCS
14 400 bit/s V.17 14 400 bit/s, ITU-T Rec. V.17 T.30, Table 2, bits 11 to 14, DCS
33 600 bit/s V.34 The title of V.34, in our fax standards table

The machines agree on a rate at the start of the call, and a call can step down to a slower one. This page uses the rate you pick for every page.

The minimum scan line time is the least time one coded line takes, so that the receiving machine can print it. A line with fewer bits than that gets fill. T.4 offers these times, and the calling machines agree on one before the pages.

a) 20 milliseconds recommended standard; ITU-T T.4, clause 3.1

b) 10 milliseconds recognized option with a mandatory fall-back to the 20 milliseconds standard; ITU-T T.4, clause 3.1

c) 5 milliseconds recognized option with a mandatory fall-back to the 10 milliseconds option and the 20 milliseconds standard; ITU-T T.4, clause 3.1

d) 0 millisecond recognized option with a mandatory fall-back to the 5 milliseconds option, the 10 milliseconds option and the 20 milliseconds standard, and an optional fall-back to the 40 milliseconds option; ITU-T T.4, clause 3.1

e) 40 milliseconds recognized option. ITU-T T.4, clause 3.1

The identification and choice of this minimum transmission time is to be made in the pre-message (phase B) portion of T.30 control procedure. ITU-T T.4, clause 3.1

T.4 names 20 ms as the standard, so the page starts there. T.4 also has an option where fine resolution takes half the time of standard. This page applies one time to both, the first alternative.

1) Alternative 1, where the minimum transmission time of the total coded scan line is the same both for the standard resolution and for the optional higher resolution: ITU-T T.4, clause 3.1

At 33 600 bit/s the page sets the time to 0 ms, because V.34 always runs in error correction mode. That mode also sends the data in frames, which the figure leaves out.

The use of the Error Correction Mode (ECM) is mandatory for all facsimile messages using the V.34 modulation system. ITU-T T.30, clause F.3

The optional T.4 error correction mode of operation and IAFD mode require 0 ms of the minimum scan line time capability. ITU-T T.30, Table 2, note 8

For the optional error correction mode, an HDLC frame structure is utilized to transmit the total coded scan line. ITU-T T.4, clause 3.3

How large is a page before it is coded?

Without a file, here is the size of a blank page before any coding, one bit per pel. It is a reference for scale, not a time. How much coding saves depends on what is on the page.

Scan lines and uncoded bits of a blank page, at 1728 pels a line
PaperStandardFine
US Letter1,071 lines, 1,850,688 bits2,142 lines, 3,701,376 bits
A41,143 lines, 1,975,104 bits2,287 lines, 3,951,936 bits

What does this page leave out?

How is the file read?

A PDF is drawn by pdf.js 6.5.438, an open source PDF reader, served from this site. A TIFF is read by our own code, the reader of the fax TIFF page with a decoder for its pixels. Both load only after you pick a file, and they work in separate threads of your browser. If its drawing thread fails, pdf.js draws on the page's own thread instead.

The coder behind the figures is faxforagents-fax-time, our open source package under the MIT licence.

A TIFF can be black and white or 8-bit grey or colour, stored uncompressed or in a fax, LZW, PackBits or Deflate coding. A file over the upload limit of 25 MiB is not read, and a document is read up to 200 pages. To check a PDF's page size and smallest text, use the fax-ready PDF page.

A file gets 120 seconds. After that the reading stops and the results show the pages done so far. A heavy page drawn on the page's own thread can take longer. The file stays on your device. The site's analytics count the visit, as on every page, and are told to leave the results out. Reload the page and the results of a file are gone.

A link to a result keeps its numbers after the # of its address, a part a browser never sends to a server. An analytics tool that records the whole address of a page can still see them.

Which code words does the page use?

These are Tables 2 and 3a of T.4, as clause 4.1 gives them. We copied them from the text of T.4 (07/03), in English, as a PDF and read them again on . The EOL is 000000000001.

White runs, 91 code words
White run lengths and their code words, Tables 2 and 3a of T.4
Run lengthCode word
000110101
1000111
20111
31000
41011
51100
61110
71111
810011
910100
1000111
1101000
12001000
13000011
14110100
15110101
16101010
17101011
180100111
190001100
200001000
210010111
220000011
230000100
240101000
250101011
260010011
270100100
280011000
2900000010
3000000011
3100011010
3200011011
3300010010
3400010011
3500010100
3600010101
3700010110
3800010111
3900101000
4000101001
4100101010
4200101011
4300101100
4400101101
4500000100
4600000101
4700001010
4800001011
4901010010
5001010011
5101010100
5201010101
5300100100
5400100101
5501011000
5601011001
5701011010
5801011011
5901001010
6001001011
6100110010
6200110011
6300110100
6411011
12810010
192010111
2560110111
32000110110
38400110111
44801100100
51201100101
57601101000
64001100111
704011001100
768011001101
832011010010
896011010011
960011010100
1024011010101
1088011010110
1152011010111
1216011011000
1280011011001
1344011011010
1408011011011
1472010011000
1536010011001
1600010011010
1664011000
1728010011011
Black runs, 91 code words
Black run lengths and their code words, Tables 2 and 3a of T.4
Run lengthCode word
00000110111
1010
211
310
4011
50011
60010
700011
8000101
9000100
100000100
110000101
120000111
1300000100
1400000111
15000011000
160000010111
170000011000
180000001000
1900001100111
2000001101000
2100001101100
2200000110111
2300000101000
2400000010111
2500000011000
26000011001010
27000011001011
28000011001100
29000011001101
30000001101000
31000001101001
32000001101010
33000001101011
34000011010010
35000011010011
36000011010100
37000011010101
38000011010110
39000011010111
40000001101100
41000001101101
42000011011010
43000011011011
44000001010100
45000001010101
46000001010110
47000001010111
48000001100100
49000001100101
50000001010010
51000001010011
52000000100100
53000000110111
54000000111000
55000000100111
56000000101000
57000001011000
58000001011001
59000000101011
60000000101100
61000001011010
62000001100110
63000001100111
640000001111
128000011001000
192000011001001
256000001011011
320000000110011
384000000110100
448000000110101
5120000001101100
5760000001101101
6400000001001010
7040000001001011
7680000001001100
8320000001001101
8960000001110010
9600000001110011
10240000001110100
10880000001110101
11520000001110110
12160000001110111
12800000001010010
13440000001010011
14080000001010100
14720000001010101
15360000001011010
16000000001011011
16640000001100100
17280000001100101